ASTM D(). Standard Guide for Testing Coating Powders and Powder Coatings. standard by ASTM International, 06/01/ View all product . Purchase your copy of ASTM D – 06() as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. Mitsubishi GT06 Autotitrator. P-E Headspace .. Coating. Provider. From ASTM. D 5 Samples from powder coating lot to be used. 5.

Author: Arashigore Akinok
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Science
Published (Last): 9 December 2015
Pages: 444
PDF File Size: 10.75 Mb
ePub File Size: 5.63 Mb
ISBN: 683-9-69242-177-6
Downloads: 78351
Price: Free* [*Free Regsitration Required]
Uploader: Grosar

ASTM D – 06() – Standard Guide for Testing Coating Powders and Powder Coatings

Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. Add to Alert PDF.

Worldwide Standards We can source any standard from anywhere in the world. A deviation from the standard bake must be agreed upon between the purchaser and seller. Some SCAB test methods will also include an accelerating weathering test see Section 36 of this guide. For the reported hiding power to be signi? This ensures that you are always up-to-date and saves you both time and money.

The type, application, and treatment of any undercoat system should be agreed upon between the purchaser and the seller. Practice G describes procedures for conditioning and handling of specimens that are being tested in laboratory accelerated or outdoor exposures.

There is no consistent correlation between the two tests. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Last previous edition D — Outdoor Exposures Natural For thermoplastic materials, no chemical reaction takes place. Abrasion resistance Air blast abrasion tester Falling sand method Taber abraser Adhesion Tape adhesion Chemical resistance Household chemical resistance Detergent resistance Acid resistance Stains or reagents on wood substrates Chip resistance Gravelmeter Edge coverage Electrical insulation Elongation?

  GUIA FOCALINUX PDF

As the voice of the U. The selection of substrate, the coating system, the manner in which the coating is scribed, the location or position of the panels within the cabinet, the length of the adtm, the inspection of panels time intervals and tests to be runand the method of reporting results must be agreed upon between the purchaser and the seller.

Your Alert Profile lists the documents that will be monitored. A good correlation between this type of dd3451 and visual evaluation has been reported. Refer to Practice D and local air quality regulations. Therefore, these test parameters should be agreed upon between the purchaser and the seller.

d34551

ASTM D3451 – 06(2017)

The cured weight loss may be requested in order to properly determine the exhaust requirements of a bake oven or to comply with state or federal reporting guidelines. Please first verify your email before subscribing to alerts. Atsm should be noted that many of the methods used for characterizing a coating powder, such as gel time Section 16 and inclined flow Section 17are primarily meant for the relative comparison of two coating powders, rather than to give a test value that can be interpreted as good or bad.

Subscription pricing is determined by: There are many types of abrasion tests available and often one, more than the others, will best simulate the abrasion resistance required in a particular end use application. The test methods included are listed in Table 1.

In either case, it is important that the viewing and measurement conditions under which color difference is to be evaluated are agreed upon between the purchaser and seller see Your comments are invited either for revision of this standard or for additional standards and should asmt addressed to ASTM Headquarters.

Interpretation of the test results will depend on the specific application in question and will also often depend on the chemistry of the coating powder used.

  DUSZA WOJOWNIKA PORADNIK PDF

It should be noted that many of the methods used for characterizing a coating powder, such as gel time Section 16 and inclined flow Section 17are primarily meant for the relative comparison of two coating powders, rather than to give a test value that can be interpreted as d33451 or bad.

For a very smooth cured? Already Subscribed to this document. Your Alert Profile lists the documents that will be monitored.

However, it emits a signi? Usage of paint systems is so varied that no one set of conditions length or place of exposure can ashm given in this guide to cover all situations. Please download Chrome or Firefox or view our browser tips. If need be, color can also be visually evaluated using Practice Dwhich determines the Munsell Coordinates of the color of a coated surface.

Your basket is empty. The test methods included are listed in Table 1. Information on current test procedures for pipe and reinforced steel bar coating powders and powder coatings can be obtained through their respective ASTM Subcommittees, A Test for salt spray in accordance with Practice B Numerical ratings derived from this type of instrument have proven difficult to correlate with subjective visual evaluation.

Please first log in with a verified email before subscribing to alerts. D Also, it is recommended that comparisons in arti? Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work. Click to learn more. The moment new editions of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email.

The following test method indicated has been found suitable for this purpose. Standards Subsctiption may be the perfect solution.