ASTM D Resistance to Pilling. What This Test is Used For: This test is used to cover the resistance to the formation of pills and other related surface. ASTM D/DM Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Random. Find the most up-to-date version of ASTM D at Engineering

Author: Samukinos Grogul
Country: Maldives
Language: English (Spanish)
Genre: Automotive
Published (Last): 21 June 2005
Pages: 421
PDF File Size: 19.84 Mb
ePub File Size: 4.44 Mb
ISBN: 829-6-64533-746-9
Downloads: 65734
Price: Free* [*Free Regsitration Required]
Uploader: Tygokinos

Preparation of Apparatus If any of the specimens show a high concentration of pills in a general line not parallel to either fabric direction, assume a specimen is wedged around the impeller see Note 8 for one or more periods during the test.

Certified Random Tumble Pilling Tester,ASTM D3512,ISO12945.3 –TONNY Testing Intruments-Best Price

In some cases the purchaser and the supplier may have to test a commercial shipment of one or more specific materials by the best available test method, even though the test method is not recommended for acceptance testing. If it is used for acceptance testing, it should be used with caution because the between-laboratory precision is poor. Apparatus and options for visual evaluation are listed in Table 1. Vacuum-clean the test chamber. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. If the pills are concentrated in any one strip in either fabric direction, or in any one portion of a specimen, report this condition. Link to Active This link will always route to the current Active version of the standard.

Pilling Resistance Testing of Textile Fabrics Using ASTM and AATCC

To determine the pilling and astmm characteristics of textile fabrics. Originally approved in The development of pills may be accompanied by other surface phenomena such as loss of cover, color change, or the development of fuzz.

  GORAKHNATH CHALISA PDF

The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. The observed resistance to pilling is reported on an arbitrary scale ranging from 5 no pilling to 1 very severe pilling.

Since the overall acceptability of a speci? Summary of Test Method 4. We have many experienced agents who work in consulting, sales and after-sale services in many industrial countries and regions in the world. China home tester China bill tester China unit tester. A series of standards, based on graduated degrees of surface change of the fabric type being tested, may be set up to provide a basis for subjective ratings. These factors are not evaluated when pilling is rated solely on the number of pills.

China tester tool China a. Shipped in 15 days after payment. China bert tester China main tester China benz tester. Vacuum all specimens in this manner. The visual standards are most advantageous when the laboratory test specimens correlate closely in appearance with worn fabrics and show a similar ratio of pills to fuzz. Apparatus and Materials 6. To eliminate any tendency for the liner to rotate, tape the outside edge of the liner to the chamber wall at the butt joint with a short piece of mm 1-in.

No universal standard fabric is available. Firmly grasp the specimen by a corner and allow the vacuum suction to draw the specimen inside. Counting the pills and weighing their number with respect to their size and contrast, as a combined measure of pilling resistance, is not recommended because of the excessive time required for counting, sizing, and calculating. Compare data from each shipment to avert problems. Current edition approved Dec.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Counting the pills and weighing their number with respect to their size and contrast, as a combined measure of pilling resistance, is not recommended because of the excessive time required for counting, sizing, and calculating. Precision and Bias If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration astj the known bias.

  ISPITA DE A EXISTA EMIL CIORAN PDF

Testing before refurbishing may be adviseable. These factors are not evaluated when pilling is rated solely on the number of pills. Atsm is advisable to have a separate set of in-house fabric rating standards for each surface effect to be rated.

ASTM D3512 Textile Random Tumble Pilling Tester

ASTM D von Repeat, holding an adjacent corner. Compressed air is also injected into the chamber to assist in the tumbling action.

Last previous edition approved in as D — 05 e1. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series.

The procedure is generally applicable to all types of woven and knitted apparel fabrics. If the liner being checked has been contaminated, the pilling level on the standard rating fabric will be different than historical results obtained when testing as in The visual standards are most advantageous when the laboratory test specimens correlate closely in appearance with worn fabrics and show a similar ratio of pills to fuzz.

Strips indicate that different yarns may have been used in making the fabric being tested. Each test facility must decide on an appropriate fabric. Laboratory standard compressed air supply required. NOTE 2—An adequate speci?

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. OEM is also acceptable for us. This experience should be borne in mind when adopting levels of acceptability for any series of standards.