BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.
|Published (Last):||26 September 2015|
|PDF File Size:||3.33 Mb|
|ePub File Size:||15.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
This is the home theatre setting for balanced operation Or use this setting with any systems where the volume control rotation is limited to the bottom half of the control or less. Bryston will custom build cables for your application.
Any amplifier that is constantly operated into clipping brystkn a more powerful amplifier is needed for that application.
Bryston 4BSST User Manual | 8 pages | Also for: 3BSST
This includes parts, labour and return shipping to the first owner and all subsequent owners. Use paired wire szt 22 to 18 gage sufficient in length between the source device and the SST amplifier.
The 1v setting provides the most amplifier gain – 29 dB. Bryston can provide an optional fan package if required.
Bryston 4B SST Stereo Amplifier User Manual
This warranty is considered void if the defect, malfunction or failure of the product or any component part was caused by damage not resulting from a defect or malfunction or abuse while in the possession of the customer. In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we gryston necessary, to restore the product to full performance.
Additional tightening pressure can be achieved using a coin in the slots of the knob. The RED binding post is connected to the amplifier output.
The amplifier will now power-up only when the control voltage is present on. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file brgston Bryston. The SST control circuitry itself draws less than 2 mA from the control current when operating. Installation see rack mounting section if applicable Ventilation. The most important nryston consideration is ventilation. In the unlikely event you have a problem and must return it for service you must use the proper packing material.
Graph shows that distortion is essentially unaffected by load. Tampering by persons other than factory authorized service personnel, or failure to fully comply with Bryston operating instructions, voids the warranty.
Push firmly the center of the switch until the power-up sequence begins. The balanced input requires a balanced pre-amp source.
Clipping flashing red Clipping occurs when the channel output level no longer can follow the level increase at the input Overdriven input condition.
The circuit feeding the 4B SST should be sufficient so as not to cause the circuit breaker to trip 15 amp min. Should the breaker trip, lower or remove the amplifier input signals.
The optimum gain setting will depend upon the source pre-amp operating level, and or personal preference. Should your instillation conditions be constricted, then additional forced air-cooling may be necessary.
Do not install directly above other heat generating equipment. The SST amplifier uses a magnetic-trip circuit breaker 1 to protect the amplifier.
Stripped bare wire up to 3 gage can be inserted through the hole in the binding post and held in place by tightening the post knob.
It’s a community-based project which helps to repair anything. The manuzl noise ratings represent minimum readings, actual readings may be better. Gold plated spade lugs are available from Bryston. Banana plugs offer a quick disconnect option. Push again and the amplifier will power-down.
Bryston 4B SST User’s Manual |
Sts the channel has cooled to a safe operating condition the channel will return to normal operation. See diagram for details. The speaker binding posts will accept wire up to 3 gage in size. Connect to this post the – terminal on the loudspeaker. See figure 2 below. Spade lugs provide high contact area and secure fastening. The 2v setting provides an amplifier gain – 23 dB.
The Output binding posts provide three different interconnect options. Also see installation section on ventilation. Balanced input Vs Single ended input: Wiring the SST amplifier also see rear panel description Speaker wires should be as short as practical.